🇬🇧 ENGLISH
Titanium Threaded Tee

Titanium Threaded Tee

Titanium threaded tees supplied as equal or reducing forms by grade, run and branch sizes, thread standard, service conditions, inspection and traceability.

Material
Titanium Grade 2, Grade 7 or Grade 12 as specified
Product Standard
ASME B16.52 for covered titanium forged threaded fittings; approved order controls
Dimensions
ASME B16.52 and ASME B1.20.1 NPT, or approved drawing
Documents
MTC, dimensions and heat/lot traceability
CONTACT US

Product Detail

Product Introduction

Titanium threaded tees divide or combine flow through a threaded branch connection. Define equal or reducing configuration, titanium grade, run and branch NPS, thread gender and designation at all three ports, pressure and temperature basis, flow service, sealing method, inspection and documentation.

Product Specifications

ProductTitanium Threaded TeeMaterial OptionsTitanium Grade 2, Grade 7 or Grade 12 as specified
FormsEqual threaded tee or reducing threaded tee with three defined portsTypical Inquiry RangeNPS 1/8 to 4 typical inquiry range; run and branch sizes must be stated separately
Product StandardASME B16.52 for covered titanium forged threaded fittings; approved order controlsDimensional BasisASME B16.52 and ASME B1.20.1 NPT, or the expressly specified thread standard
WallSchedule or nominal wall thickness matched to the connected pipe and designEndsFemale NPT ports typical; male, BSPT/BSPP or drawing-specific ports by order
ManufacturingSeamless, welded, formed, forged, machined or fabricated as specifiedSurfacePickled, cleaned, machined or project-specific finish
InspectionVisual, dimensions, wall, ends and specified NDTDocumentsMTC, heat/lot traceability and inspection report

Typical ranges are quotation guidance, not a stock guarantee. Final availability and tolerances are confirmed against the complete RFQ and design code.

Selection and Configuration

  • Material compatibility: Match the fitting grade, source product and welding procedure to the connected titanium pipe and service environment.
  • Dimensional definition: State NPS or outside diameter, wall thickness or schedule, center-to-end dimensions and end preparation.
  • Fabrication route: Specify seamless, welded, formed, forged, machined or drawing-controlled construction as applicable.
Pressure-design note: Dimensional conformity does not by itself establish pressure rating. The piping designer must verify material allowable stress, wall thickness, weld joint, corrosion allowance, temperature and governing construction code.

Send the piping specification or drawing
Include grade, NPS or OD, wall/schedule, geometry, ends, quantity, tests and documents.

Request a Quotation

Chemical Composition

Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered grade controls.

Grade / UNSPdMo / NiFeOCNHTi
Grade 2 / R50400——0.300.250.080.030.015Balance
Grade 7 / R524000.12–0.25 Pd—0.300.250.080.030.015Balance
Grade 12 / R53400—0.20–0.40 Mo; 0.60–0.90 Ni0.300.250.080.030.015Balance

Mechanical Properties – Annealed Source Material Reference

GradeUltimate Tensile Strength min0.2% Yield Strength minElongation min
Grade 2345 MPa (50 ksi)275 MPa (40 ksi)20%
Grade 7345 MPa (50 ksi)275 MPa (40 ksi)20%
Grade 12483 MPa (70 ksi)345 MPa (50 ksi)18%

Representative wrought-source material minima. Fitting acceptance, heat treatment and test specimens must follow the ordered material/product specification and size.

Typical Physical Properties

GradeDensityElastic ModulusThermal ConductivityThermal Expansion
Grade 24.51 g/cm³Approx. 105 GPaApprox. 16.4 W/m·KApprox. 8.6 µm/m·K
Grade 7Approx. 4.51 g/cm³Approx. 105 GPaApprox. 16 W/m·KApprox. 8.6 µm/m·K
Grade 12Approx. 4.54 g/cm³Approx. 103 GPaApprox. 16 W/m·KApprox. 8.6 µm/m·K

Typical engineering references, not inspection acceptance limits.

Certificates & Inspection Records

SAKY ALLOY quality management system certificate

Services We Can Provide

Specification ReviewGrade, dimensions, wall, ends and code requirements.
Custom FabricationLarge, non-standard and drawing-specific geometry by review.
End PreparationBevel, socket, thread, machined or project-defined ends.
NDT CoordinationPT, RT and other agreed examinations with reports.
TraceabilityMTC, heat/lot records and dimensional inspection.
Export SupportProtected packing, labels and shipping documents.

Product Packaging

Fittings are capped or wrapped to protect clean ends, bevels, threads and machined faces. Items are separated by grade, size and heat/lot, then packed in reinforced cartons or export cases according to geometry and quantity.

Application Scenarios

Chemical processing plant with industrial process piping

Chemical Processing

Corrosion-resistant piping for acids, chlorides and process media after grade compatibility review.

Wind turbines and solar panels at a renewable energy site

Power & Energy

Cooling-water, condenser and auxiliary piping requiring traceable titanium components.

Cargo vessel moored for marine service

Marine & Desalination

Seawater and chloride-bearing piping systems designed for the selected titanium grade.

FAQ

What information is required to quote Titanium Threaded Tee?

Provide the titanium grade, product form, dimensional standard or drawing, thread or critical dimensions, quantity, surface treatment, mating parts, service conditions and required inspection documents.

Which standards apply to Titanium Threaded Tee?

ASME B16.52 applies to covered titanium forged threaded fittings; ASME B1.20.1 may define NPT threads when invoked. State equal or reducing form, run and branch sizes, grade, service conditions and inspection.

How are Titanium Threaded Tee inspected?

Available controls include MTC review, visual and dimensional inspection, wall-thickness checks, end preparation, dye-penetrant examination, radiography or other NDT when specified, and heat/lot traceability.

Leave Your Message

Related Technical Guides

WhatsApp