🇬🇧 ENGLISH

Titanium Threaded Elbow

Titanium threaded elbows supplied by grade, 45° or 90° angle, NPS at both ends, thread standard, service conditions, inspection and traceability.

Material: Titanium Grade 2, Grade 7 or Grade 12 as specified
Product Standard: ASME B16.52 for covered titanium forged threaded fittings; approved order controls
Dimensions: ASME B16.52 and ASME B1.20.1 NPT, or approved drawing
Documents: MTC, dimensions and heat/lot traceability

Product Detail

Product Introduction

Titanium threaded elbows change piping direction through a compact threaded connection. Define 45° or 90° angle, titanium grade, NPS at both ends, female or male thread, thread designation and gaging, pressure and temperature basis, service medium, sealing method, inspection and documentation.

Product Specifications

Product	Titanium Threaded Elbow	Material Options	Titanium Grade 2, Grade 7 or Grade 12 as specified
Forms	45-degree or 90-degree threaded elbow; equal or reducing ends by approved order	Typical Inquiry Range	NPS 1/8 to 4 typical inquiry range; state both end sizes for a reducing elbow
Product Standard	ASME B16.52 for covered titanium forged threaded fittings; approved order controls	Dimensional Basis	ASME B16.52 and ASME B1.20.1 NPT, or the expressly specified thread standard
Wall	Schedule or nominal wall thickness matched to the connected pipe and design	Ends	Female NPT ends typical; male, BSPT/BSPP or drawing-specific ends by order
Manufacturing	Seamless, welded, formed, forged, machined or fabricated as specified	Surface	Pickled, cleaned, machined or project-specific finish
Inspection	Visual, dimensions, wall, ends and specified NDT	Documents	MTC, heat/lot traceability and inspection report

Typical ranges are quotation guidance, not a stock guarantee. Final availability and tolerances are confirmed against the complete RFQ and design code.

Selection and Configuration

Material compatibility: Match the fitting grade, source product and welding procedure to the connected titanium pipe and service environment.
Dimensional definition: State NPS or outside diameter, wall thickness or schedule, center-to-end dimensions and end preparation.
Fabrication route: Specify seamless, welded, formed, forged, machined or drawing-controlled construction as applicable.

Pressure-design note: Dimensional conformity does not by itself establish pressure rating. The piping designer must verify material allowable stress, wall thickness, weld joint, corrosion allowance, temperature and governing construction code.

Send the piping specification or drawing
Include grade, NPS or OD, wall/schedule, geometry, ends, quantity, tests and documents.

Request a Quotation

Chemical Composition

Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered grade controls.

Grade / UNS	Pd	Mo / Ni	Fe	O	C	N	H	Ti
Grade 2 / R50400	—	—	0.30	0.25	0.08	0.03	0.015	Balance
Grade 7 / R52400	0.12–0.25 Pd	—	0.30	0.25	0.08	0.03	0.015	Balance
Grade 12 / R53400	—	0.20–0.40 Mo; 0.60–0.90 Ni	0.30	0.25	0.08	0.03	0.015	Balance

Mechanical Properties – Annealed Source Material Reference

Grade	Ultimate Tensile Strength min	0.2% Yield Strength min	Elongation min
Grade 2	345 MPa (50 ksi)	275 MPa (40 ksi)	20%
Grade 7	345 MPa (50 ksi)	275 MPa (40 ksi)	20%
Grade 12	483 MPa (70 ksi)	345 MPa (50 ksi)	18%

Representative wrought-source material minima. Fitting acceptance, heat treatment and test specimens must follow the ordered material/product specification and size.

Typical Physical Properties

Grade	Density	Elastic Modulus	Thermal Conductivity	Thermal Expansion
Grade 2	4.51 g/cm³	Approx. 105 GPa	Approx. 16.4 W/m·K	Approx. 8.6 µm/m·K
Grade 7	Approx. 4.51 g/cm³	Approx. 105 GPa	Approx. 16 W/m·K	Approx. 8.6 µm/m·K
Grade 12	Approx. 4.54 g/cm³	Approx. 103 GPa	Approx. 16 W/m·K	Approx. 8.6 µm/m·K

Typical engineering references, not inspection acceptance limits.

Certificates & Inspection Records

SAKY ALLOY quality management system certificate

Services We Can Provide

Specification ReviewGrade, dimensions, wall, ends and code requirements.

Custom FabricationLarge, non-standard and drawing-specific geometry by review.

End PreparationBevel, socket, thread, machined or project-defined ends.

NDT CoordinationPT, RT and other agreed examinations with reports.

TraceabilityMTC, heat/lot records and dimensional inspection.

Export SupportProtected packing, labels and shipping documents.

Product Packaging

Fittings are capped or wrapped to protect clean ends, bevels, threads and machined faces. Items are separated by grade, size and heat/lot, then packed in reinforced cartons or export cases according to geometry and quantity. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.

Titanium elbows and return bends protected in export packaging

Application Scenarios

Chemical Processing

Corrosion-resistant piping for acids, chlorides and process media after grade compatibility review.

Wind turbines and solar panels at a renewable energy site

Power & Energy

Cooling-water, condenser and auxiliary piping requiring traceable titanium components.

Marine & Desalination

Seawater and chloride-bearing piping systems designed for the selected titanium grade.

FAQ

What information is required to quote Titanium Threaded Elbow?

Provide the titanium grade, product form, dimensional standard or drawing, thread or critical dimensions, quantity, surface treatment, mating parts, service conditions and required inspection documents.

Which standards apply to Titanium Threaded Elbow?

ASME B16.52 applies to covered titanium forged threaded fittings; ASME B1.20.1 may define NPT threads when invoked. State angle, both end sizes, grade, service conditions and inspection.

How are Titanium Threaded Elbow inspected?

Available controls include MTC review, visual and dimensional inspection, wall-thickness checks, end preparation, dye-penetrant examination, radiography or other NDT when specified, and heat/lot traceability.