Titanium Clevis Pins
Titanium clevis pins supplied by grade, shank diameter, usable length, head form, cross-hole location, retainer, fit and inspection requirements.
- Material
- Titanium Grade 2 or Grade 5 as specified
- Form
- Headed pin with transverse retainer hole
- Dimensions
- Diameter, grip length, head and cross-hole
- Documents
- MTC, dimensional report and lot traceability
Product Detail
Product Introduction
Titanium clevis pins form removable pivot or linkage connections when retained by a cotter pin, clip or other approved device. The order must define grade, shank diameter and fit, usable or grip length, head geometry, cross-hole diameter and location, end chamfer, retainer, load direction, wear surfaces and inspection.
Product Specifications
| Product | Titanium Clevis Pins | Grade | Titanium Grade 2 or Grade 5 |
|---|---|---|---|
| Standard | ISO 2341, DIN 1444 or drawing-specific clevis-pin dimensions may be referenced when expressly invoked. Their standard material requirements do not automatically define titanium; the order must separately state grade, condition, finished-pin properties, retainer and deviations. | Size & Form | Shank diameter and tolerance, usable length, head, cross-hole diameter/location, chamfer and retainer by drawing or invoked reference |
| Tolerance | Drawing-defined diameter, length, straightness, head concentricity and cross-hole position | Supply Condition | Cold headed or machined, cross-drilled, deburred, cleaned and lot identified |
| Inspection | Available controls include MTC review, shank diameter, length, head, cross-hole diameter and position, straightness, surface finish, visual condition and heat or lot traceability. | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 2 / R50400 | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 5 / R56400 | Al 5.50–6.75; V 3.50–4.50 | 0.40 | 0.20 | 0.08 | 0.05 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 2 | 345 MPa | 275 MPa | 20% |
| Grade 5 | 895 MPa | 828 MPa | 10% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 8.6 µm/m·K |
| Grade 5 | 4.43 g/cm³ | Approx. 114 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Products are separated by grade and heat, protected against surface and dimensional damage, and packed with traceability labels according to form, size, quantity and shipping method.
Application Scenarios
Marine linkages, hatches and corrosion-resistant equipment
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Aerospace controls, fixtures and lightweight mechanisms
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Chemical-process machinery and removable equipment joints
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
How is a clevis pin different from a dowel pin?
A clevis pin is normally a removable retained connection with a head and cross-hole; a dowel pin primarily locates or aligns components through a controlled fit.
Is the cotter pin included?
Only when the RFQ defines retainer type, material, size and quantity. The complete retention stack should be specified.
Which dimensions are critical?
Shank diameter and fit, usable length, head, cross-hole diameter and location, straightness and surface finish are typically controlled.
Leave Your Message
Related Technical Guides
Titanium Solid Rivets vs Blind Rivets
Compare access, installation, head style, grip range and inspection.
Read technical guideHow to Specify Titanium Dowel Pins
Define diameter, fit, length, ends, surface and inspection.
Read technical guideRivets and Dowel Pins Application Guide
Review joint function, material compatibility and purchasing data.
Read technical guideTitanium Clevis Pins vs Dowel Pins
Compare retention, alignment, fit, cross-hole and ordering data.
Read technical guideHow to Specify Titanium Retaining Rings
Define internal or external type, groove, section, load and installation.
Read technical guidePins and Retaining Rings Application Guide
Review material compatibility, joint function and inspection.
Read technical guide