Titanium Spacers and Standoffs
Precision titanium spacers and standoffs supplied in round or hex form with bore or male/female threads, controlled length, flats, ends, surface and inspection.
- Material
- Titanium Grade 2 or Grade 5 as specified
- Forms
- Round spacer; hex or round standoff
- Threads
- Female-female, male-female or drawing-defined
- Documents
- MTC, dimensions and lot traceability
Product Detail
Product Introduction
Titanium spacers maintain a controlled separation between components, while standoffs add internal or external threads for fastening. A complete definition includes round or hex body, bore or thread combination, across-flats or outside diameter, body length, male-thread projection, end squareness, concentricity, load direction, mating hardware and inspection.
Product Specifications
| Product | Titanium Spacers and Standoffs | Grade | Titanium Grade 2 or Grade 5 |
|---|---|---|---|
| Standard | Common commercial standoff dimensions may be used only as purchasing references. Titanium supply is normally drawing-controlled because body length, thread engagement, flats, shoulders, strength and installation requirements vary by assembly. | Size & Form | Round or hex body; OD/across-flats, bore or thread combination, body length, projections, shoulders and ends by drawing |
| Tolerance | Drawing-defined length, bore/thread, flats, squareness, concentricity and male-thread projection | Supply Condition | CNC turned or milled, thread inspected, deburred, cleaned and lot identified |
| Inspection | Available controls include MTC review, bore or thread gauging, outside diameter or across-flats, body length, male projection, end squareness, concentricity, surface finish, visual condition and lot traceability. | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 2 / R50400 | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 5 / R56400 | Al 5.50–6.75; V 3.50–4.50 | 0.40 | 0.20 | 0.08 | 0.05 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 2 | 345 MPa | 275 MPa | 20% |
| Grade 5 | 895 MPa | 828 MPa | 10% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 8.6 µm/m·K |
| Grade 5 | 4.43 g/cm³ | Approx. 114 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Products are separated by grade and heat, protected against surface and dimensional damage, and packed with traceability labels according to form, size, quantity and shipping method.
Application Scenarios
Marine electrical, instrument and enclosure assemblies
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Aerospace panels, fixtures and lightweight equipment supports
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Chemical-process controls, sensors and corrosion-resistant equipment spacing
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
What is the difference between a spacer and a standoff?
A spacer normally has a clearance bore and controls separation around a fastener; a standoff includes internal or external threads for direct attachment.
Which length should be specified?
State the body or separation length independently from any male-thread projection, shoulder or end feature.
Can hex and round forms be interchanged?
Only after confirming wrench access, envelope, bearing area, torque, load and drawing approval.
Leave Your Message
Related Technical Guides
Titanium Solid Rivets vs Blind Rivets
Compare access, installation, head style, grip range and inspection.
Read technical guideHow to Specify Titanium Dowel Pins
Define diameter, fit, length, ends, surface and inspection.
Read technical guideRivets and Dowel Pins Application Guide
Review joint function, material compatibility and purchasing data.
Read technical guideTitanium Clevis Pins vs Dowel Pins
Compare retention, alignment, fit, cross-hole and ordering data.
Read technical guideHow to Specify Titanium Retaining Rings
Define internal or external type, groove, section, load and installation.
Read technical guidePins and Retaining Rings Application Guide
Review material compatibility, joint function and inspection.
Read technical guideTitanium Cotter Pins vs Spring Pins
Compare removable retention with interference-fit location and retention.
Read technical guideHow to Specify Titanium Spring Pins
Define pin form, hole limits, interference, insertion force and validation.
Read technical guideTitanium Pin Retention Systems Guide
Select clevis, cotter, spring pin and retaining-ring systems by joint function.
Read technical guideTitanium Threaded Inserts vs Tapped Holes
Compare repair, thread durability, wall section, locking and serviceability.
Read technical guideHow to Specify Titanium Spacers and Standoffs
Define body form, threads, length, fits, loads and inspection.
Read technical guideTitanium Inserts, Spacers and Standoffs Guide
Review assembly function, interfaces, galvanic exposure and purchasing data.
Read technical guide