🇬🇧 ENGLISH

Grade 2 Titanium U-Bolts

Commercially pure Grade 2 titanium U-bolts for corrosion-resistant clamps, supports and equipment attachments. Geometry, thread, forming condition, mating hardware, finish and inspection follow the approved drawing.

Material: Grade 2 / UNS R50400
Forms: Round, square or drawing-specific
Threads: Metric, UNC, UNF or drawing
Documents: MTC, dimensions and traceability

Product Detail

Product Introduction

Grade 2 U-bolts are drawing-controlled formed fasteners for corrosion-resistant clamps and supports. The RFQ must define inside width, leg length, bend radius, rod diameter, thread coverage, mating hardware, service load and inspection.

Product Specifications

Product	Grade 2 Titanium U-Bolts	Material	Titanium Grade 2 (UNS R50400)
Product Form	Round, square or drawing-specific U-bolt	Typical Inquiry Range	M6 to M30 rod diameter typical inquiry range; leg spacing and length by drawing
Dimensional References	Customer drawing, DIN, ASME or project specification when invoked	Threads / Dimensions	Metric coarse or fine, UNC, UNF or drawing-specific as applicable
Surface	Machined and cleaned; lubricant, anti-galling treatment or coating by agreement	Documents	MTC, heat/lot traceability and dimensional inspection report
Inspection	Dimensions, thread gauging, surface and agreed functional or mechanical tests	Supply Basis	Approved purchase order, invoked standard and drawing

Typical inquiry ranges are not a stock guarantee. Final manufacturability, tolerances and test requirements are confirmed against the complete RFQ.

Selection and Configuration

Geometry: Provide center spacing or inside width, bend radius, leg length and thread coverage.
Forming route: Review bend severity, Grade 2 condition, surface acceptance and dimensional springback.
Assembly design: Confirm saddle geometry, clamp load, vibration, temperature, galvanic exposure and galling controls.

Standards and ordering definition: U-bolts are commonly supplied to approved drawings. ASME, DIN or project references apply only when expressly invoked; Grade 2 condition and finished-fastener acceptance remain separately controlled.

Send a drawing or complete fastener definition
Include dimensions, quantity, mating parts, service conditions, finish and inspection requirements.

Request a Quotation

Chemical Composition – Titanium Grade 2

Maximum weight percent unless shown otherwise; titanium is the balance.

N max	C max	H max	Fe max	O max	Residual each / total	Ti
0.03	0.08	0.015	0.30	0.25	0.10 / 0.40	Balance

Mechanical Properties – Grade 2 Material Reference

Property	Annealed Grade 2 Material Reference Minimum
Ultimate tensile strength	345 MPa (50 ksi)
0.2% yield strength	275 MPa (40 ksi)
Elongation	20%

Material values do not automatically establish finished-fastener loadability. Finished-part acceptance depends on geometry, manufacturing route, condition and the expressly invoked fastener specification or drawing.

Typical Physical Properties

Property	Typical Value
Density	4.51 g/cm³
Elastic modulus	Approximately 105 GPa
Poisson ratio	Approximately 0.34
Thermal conductivity	Approximately 16.4 W/m·K
Coefficient of thermal expansion	Approximately 8.6 µm/m·K
Melting point	Approximately 1668°C

Physical values are typical engineering references and are not inspection acceptance limits.

Certificates & Inspection Records

SAKY ALLOY quality management system certificate

Services We Can Provide

Drawing ReviewGeometry, thread, tolerances and mating-component review.

Custom ManufacturingMetric, inch and drawing-specific production subject to review.

InspectionDimensional checks, thread gauging and agreed functional testing.

Surface OptionsCleaning, identification, lubricant or coating by agreement.

TraceabilityMTC, heat/lot records and inspection documentation.

Export SupportProtected packing, labeling and shipping documents.

Product Packaging

Grade 2 Titanium U-Bolts are separated by size and lot, protected against thread and surface damage, and labeled with grade, dimensions, quantity and traceability reference. Inner bags, cartons and export cases are selected according to product geometry, quantity and shipping method.

Application Scenarios

Chemical Processing

Corrosion-resistant equipment joints selected against the complete process environment.

Wind turbines and solar panels at a renewable energy site

Power & Energy

Lightweight engineered assemblies requiring controlled dimensions and traceability.

Marine & Shipbuilding

Corrosion-resistant joints subject to galvanic, preload and service-condition review.

FAQ

What information is required to quote Grade 2 Titanium U-Bolts?

Provide the titanium grade, product form, dimensional standard or drawing, thread or critical dimensions, quantity, surface treatment, mating parts, service conditions and required inspection documents.

Which standards apply to Grade 2 Titanium U-Bolts?

U-bolts are commonly supplied to approved drawings. ASME, DIN or project references apply only when expressly invoked; Grade 2 condition and finished-fastener acceptance remain separately controlled.

How are Grade 2 Titanium U-Bolts inspected?

Available controls include MTC review, leg spacing, bend radius, symmetry, length and thread measurement, GO/NO-GO gauging, surface examination and heat/lot traceability.

Grade 2 Titanium U-Bolts