Titanium Woven Wire Mesh
Titanium Woven Wire Mesh supplied by grade, woven wire mesh geometry, opening, thickness or wire diameter, width, length, edge, surface and inspection requirements.
- Material
- Grade 1, Grade 2 or specified titanium
- Form
- Woven Wire Mesh
- Dimensions
- Opening geometry and section size by RFQ
- Documents
- MTC and dimensional inspection
Product Detail
Product Introduction
Titanium woven wire mesh is manufactured by interlacing titanium wires in a defined weave. Mesh count alone is incomplete: wire diameter and weave determine the clear opening and open area. The RFQ should state grade, plain or twill weave, mesh count or clear aperture, wire diameter, roll or panel size, edge condition, cleanliness and dimensional inspection.
Product Specifications
| Product | Titanium Woven Wire Mesh | Grade | Titanium Grade 1, Grade 2 or specified alloy |
|---|---|---|---|
| Standard | Titanium wire feedstock and finished woven mesh are supplied to the expressly invoked material requirement and an agreed mesh schedule or drawing. The order controls wire diameter, mesh count or aperture, weave, tolerances, width, length, edges and inspection. | Size & Form | Woven wire mesh in sheets, cut panels or rolls as feasible; exact opening, section dimensions, width and length by RFQ |
| Tolerance | Drawing or order-defined opening, wire/strand/sheet size, pitch, open area, cut size, edge and flatness requirements | Supply Condition | Clean mill-finish sheets, panels or rolls with edge protection, interleaving and export packing |
| Inspection | MTC and heat traceability, wire diameter, wires or openings per unit length, clear aperture, weave identity, width and length, edge condition, surface cleanliness and visual review for broken or displaced wires. | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 1 / R50250 | — | 0.20 | 0.18 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 2 / R50400 | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 1 | 240 MPa | 170 MPa | 24% |
| Grade 2 | 345 MPa | 275 MPa | 20% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 1 | 4.51 g/cm³ | Approx. 103 GPa | Approx. 8.6 µm/m·K |
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Wire is protected in coils, spools or straight-length bundles with moisture-resistant wrapping and labels for grade, diameter, heat and quantity. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.
Application Scenarios
Chemical filtration and separation
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Electrochemical electrodes and current collectors
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Marine, aerospace and industrial screening or guards
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
Is mesh count enough to specify woven titanium mesh?
No. The same mesh count with a different wire diameter produces a different clear opening and open area. State both values or specify the required aperture.
Can woven mesh be supplied as cut panels?
Yes, subject to mesh construction and edge stability. State panel dimensions, edge treatment, flatness and packaging requirements.
What causes opening variation in woven mesh?
Wire-diameter tolerance, weaving tension, crimp and handling can affect aperture. Define the measurement method, sampling and allowable variation when critical.
Leave Your Message
Related Technical Guides
Titanium Woven Mesh vs Expanded Metal vs Perforated Sheet
Compare opening geometry, strength and ordering data.
Read technical guideTitanium RFQ Checklist
Prepare dimensions, tolerances, tests and documents.
Read technical guideComplete Titanium Product Guide
Compare titanium product forms.
Read technical guide