Titanium Grade 12 Strip
Titanium Grade 12 Strip supplied as slit coil or cut strip by thickness, width, coil ID/OD, unit weight, edge, surface, tolerance, inspection and traceability requirements.
- Material
- Titanium Grade 12 / Ti-0.3Mo-0.8Ni / UNS R53400
- Standard
- ASTM B265 / ASME SB265
- Product Form
- Coil or strip; thickness, width, coil ID/OD, coil weight and edge condition are confirmed by RFQ
- Documents
- MTC, inspection and heat/lot traceability
Product Detail
Product Introduction
Titanium Grade 12 Strip is supplied for corrosion-resistant fabrication and precision manufacturing. The final purchase definition must identify the exact material designation, governing specification and revision, dimensions, condition, tolerances, tests and documentation; trade-name or cross-standard equivalence is not assumed.
Product Specifications
| Product | Titanium Grade 12 Strip | Grade | Titanium Grade 12 / Ti-0.3Mo-0.8Ni / UNS R53400 |
|---|---|---|---|
| Standard | ASTM B265 / ASME SB265 | Size & Form | Slit coil or cut strip; thickness, width, coil ID/OD, maximum unit weight, edge condition and length are confirmed by RFQ |
| Tolerance | ASTM B265 / ASME SB265 or tighter order-defined thickness, width, camber, edge and flatness requirements | Supply Condition | Cold rolled and annealed strip with slit or mill edges and pickled, descaled, bright or order-specific surface |
| Inspection | MTC review, dimensional and surface inspection, heat/lot traceability, with PMI or applicable NDT when specified | Documents | MTC, heat/lot traceability and agreed inspection reports |
Additional Supply & Ordering Details
Useful, technically consistent information consolidated from earlier product pages.
| Grade boundary | Grade 12 / UNS R53400 is Ti-0.3Mo-0.8Ni nominal alloyed titanium with higher strength and a different corrosion-selection basis than commercially pure Grade 1 strip. |
|---|---|
| Service-oriented selection | Provide process medium, concentration, temperature, contaminants, crevice geometry, forming and welding route. Grade 12 should be selected from service and fabrication data, not grade name alone. |
| Strip geometry | State thickness, width, coil ID and OD, coil weight, edge, camber, surface, condition and whether the strip will be formed, welded or clad. |
| Inspection focus | Review ASTM B265 chemistry including Mo and Ni, mechanical results, dimensional mapping, surface and edge, heat/lot traceability and any corrosion or supplementary project test. |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 1 / R50250 | — | 0.20 | 0.18 | 0.08 | 0.03 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 1 | 240 MPa | 170 MPa | 24% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 1 | 4.51 g/cm³ | Approx. 103 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Coils and slit strip are wrapped against moisture and edge damage, secured on skids or in export cases, and labeled with grade, heat, size, coil weight and edge condition. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.
Application Scenarios
Chemical-process fabrication and liners
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Heat-exchanger, gasket and precision formed components
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Marine, energy and industrial strip fabrication
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
What information is required to quote Titanium Grade 12 Strip?
Provide the titanium grade, product form, dimensional standard or drawing, thread or critical dimensions, quantity, surface treatment, mating parts, service conditions and required inspection documents.
Which standards apply to Titanium Grade 12 Strip?
ASTM B265 / ASME SB265
How are Titanium Grade 12 Strip inspected?
MTC review, dimensional and surface inspection, heat/lot traceability, with PMI or applicable NDT when specified
Leave Your Message
Related Technical Guides
Titanium Strip vs Sheet vs Foil
Compare product form, dimensional control and ordering requirements.
Read technical guideTitanium Strip Applications and Selection
Review chemical, heat-transfer, marine and precision fabrication uses.
Read technical guideTitanium Strip Grade Comparison
Compare common strip grades by strength, corrosion environment and fabrication.
Read technical guide