Grade 9 Ti-3Al-2.5V Titanium Sheet
Medium-strength Ti-3Al-2.5V sheet supplied by applicable specification, gauge, dimensions, condition, surface, forming requirements and inspection.
- Material
- Grade 9 / Ti-3Al-2.5V / UNS R56320
- Standard
- ASTM B265 / approved project specification as applicable
- Form
- Sheet, plate or cut blank as specified
- Documents
- MTC, heat/lot traceability and agreed inspection reports
Product Detail
Product Introduction
Grade 9 Ti-3Al-2.5V Titanium Sheet is ordered for a specific engineering and procurement route rather than selected from grade name alone. The RFQ must identify the governing standard and revision, grade, product dimensions, condition, surface, tests and documentation needed by the finished component manufacturer.
Product Specifications
| Product | Grade 9 Ti-3Al-2.5V Titanium Sheet | Grade | Grade 9 / Ti-3Al-2.5V / UNS R56320 |
|---|---|---|---|
| Standard | ASTM B265 / approved project specification as applicable applies only when expressly invoked and when its scope covers the ordered product form and grade. Use the purchase-order revision and do not substitute ASTM B265, ASTM F67, ASTM F136 or AMS4911 without written technical approval. | Size & Form | Sheet, plate and cut-to-size blanks by exact thickness, width, length or drawing dimensions |
| Tolerance | Applicable product standard and order-defined thickness, width, length, flatness, edge, surface and cut-blank tolerances | Supply Condition | Hot rolled or cold rolled, annealed, descaled, pickled, ground, polished, waterjet cut, saw cut or machined as agreed |
| Inspection | Review of material certificate and heat identity, chemistry and mechanical tests, thickness/width/length, flatness and surface, edge or cut-blank dimensions, plus ultrasonic, microstructure or supplementary reports when ordered. | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 9 / R56320 | Al 2.50–3.50; V 2.00–3.00 | 0.25 | 0.15 | 0.08 | 0.03 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 9 | 620 MPa | 485 MPa | 15% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 9 | Approx. 4.48 g/cm³ | Approx. 105 GPa | Approx. 9.0 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Sheet and plate surfaces are interleaved or wrapped as required, protected at edges and secured on pallets or in export cases with grade, heat and dimensional identification. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.
Application Scenarios
Aerospace and lightweight structures
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Formed sheet components and enclosures
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Sports, marine and industrial assemblies
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
Can another titanium plate standard be substituted?
Only with written technical approval. Standards can differ in scope, grade designation, condition, testing, microstructure, melt route and documentation.
Which dimensions should be included in the RFQ?
Provide thickness, width and length or a controlled drawing, tolerances, flatness, edge/cut condition and machining allowance.
What documentation can be requested?
State the required MTC, heat/lot traceability, chemistry, tensile results, dimensional report, ultrasonic or microstructure report and regulatory or aerospace documents.
Leave Your Message
Related Technical Guides
Grade 1 vs Grade 9 vs Grade 12 Sheet
Compare formability, strength, corrosion selection and purchasing data.
Read technical guideASTM B265 vs F67 vs F136 vs AMS 4911
Select a titanium plate standard by application.
Read technical guideGrade 5 vs Grade 23 Titanium Plate
Compare standard, interstitial control and purchasing intent.
Read technical guideTitanium RFQ Checklist
Prepare dimensions, tests and documents.
Read technical guide