Titanium Eccentric Reducer
Titanium Eccentric Reducer supplied by titanium grade, outside diameter or NPS, wall thickness, end preparation, dimensional standard and inspection requirements for corrosion-resistant piping systems.
- Material
- Titanium Grade 2, Grade 7 or Grade 12 as specified
- Product Standard
- ASTM B363 / ASME SB363 where applicable
- Dimensions
- ASME B16.9, B16.11 or approved drawing
- Documents
- MTC, dimensions and heat/lot traceability
Product Detail
Product Introduction
A titanium eccentric reducer connects different pipe sizes with offset end centerlines so one side can remain flat. It is used where piping layout, drainage, pump suction or prevention of vapor pockets requires a controlled orientation. The RFQ must state flat-side orientation, both end sizes and walls, offset, length, weld ends, grade and inspection.
Product Specifications
| Product | Titanium Eccentric Reducer | Material Options | Titanium Grade 2, Grade 7 or Grade 12 as specified |
|---|---|---|---|
| Forms | Concentric or eccentric reducer | Typical Inquiry Range | NPS 1/2 to 24 typical standard inquiry range; large and custom transitions by review |
| Product Standard | ASTM B363 / ASME SB363 where applicable | Dimensional Basis | ASME B16.9, ASME B16.11 or approved drawing as applicable |
| Wall | Schedule or nominal wall thickness matched to the connected pipe and design | Ends | Butt-weld bevel or drawing-defined ends |
| Manufacturing | Seamless, welded, formed, forged, machined or fabricated as specified | Surface | Pickled, cleaned, machined or project-specific finish |
| Inspection | Visual, dimensions, wall, ends and specified NDT | Documents | MTC, heat/lot traceability and inspection report |
Typical ranges are quotation guidance, not a stock guarantee. Final availability and tolerances are confirmed against the complete RFQ and design code.
Selection and Configuration
- Flat-side orientation: State flat side up, flat side down or drawing orientation; the fitting cannot be installed correctly from size alone.
- Pump and process service: Coordinate orientation with suction-line design, drainage, gas release, solids and equipment nozzle elevation.
- Offset geometry: Define large and small ends, walls, overall length, offset and end preparation to the dimensional reference or drawing.
Send the piping specification or drawing
Include grade, NPS or OD, wall/schedule, geometry, ends, quantity, tests and documents.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered grade controls.
| Grade / UNS | Pd | Mo / Ni | Fe | O | C | N | H | Ti |
|---|---|---|---|---|---|---|---|---|
| Grade 2 / R50400 | — | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 7 / R52400 | 0.12–0.25 Pd | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 12 / R53400 | — | 0.20–0.40 Mo; 0.60–0.90 Ni | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
Mechanical Properties – Annealed Source Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 2 | 345 MPa (50 ksi) | 275 MPa (40 ksi) | 20% |
| Grade 7 | 345 MPa (50 ksi) | 275 MPa (40 ksi) | 20% |
| Grade 12 | 483 MPa (70 ksi) | 345 MPa (50 ksi) | 18% |
Representative wrought-source material minima. Fitting acceptance, heat treatment and test specimens must follow the ordered material/product specification and size.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Conductivity | Thermal Expansion |
|---|---|---|---|---|
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 16.4 W/m·K | Approx. 8.6 µm/m·K |
| Grade 7 | Approx. 4.51 g/cm³ | Approx. 105 GPa | Approx. 16 W/m·K | Approx. 8.6 µm/m·K |
| Grade 12 | Approx. 4.54 g/cm³ | Approx. 103 GPa | Approx. 16 W/m·K | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Fittings are capped or wrapped to protect clean ends, bevels, threads and machined faces. Items are separated by grade, size and heat/lot, then packed in reinforced cartons or export cases according to geometry and quantity.
Application Scenarios
Chemical Processing
Corrosion-resistant piping for acids, chlorides and process media after grade compatibility review.
Power & Energy
Cooling-water, condenser and auxiliary piping requiring traceable titanium components.
Marine & Desalination
Seawater and chloride-bearing piping systems designed for the selected titanium grade.
FAQ
Why use an eccentric reducer?
Its offset allows one side to remain flat, supporting drainage, nozzle alignment or control of gas and liquid pockets.
Must flat-side orientation appear on the order?
Yes. State flat side up/down or provide a drawing because orientation is part of the functional geometry.
Can it be rotated during installation?
Only if the piping design permits the resulting flat-side orientation and process behavior.
Leave Your Message
Related Technical Guides
Titanium Butt Weld Fittings Purchasing Matrix
Compare geometry, size, wall, ends, route and inspection.
Read technical guideTitanium Fittings for Seawater Piping
Coordinate material, piping design, fabrication and inspection.
Read technical guideTitanium RFQ Checklist
Prepare complete purchasing data and documents.
Read technical guide