Precision Titanium Bushings
Precision titanium bushings and sleeves machined to drawing with controlled bore, outside diameter, concentricity, length, surface finish, grade and inspection.
- Materials
- Grade 2, Grade 5 or drawing-specified titanium
- Forms
- Straight, flanged, shouldered or grooved bushing
- Critical Features
- Bore, OD, wall, concentricity and finish
- Documents
- MTC, traceability and dimensional report
Product Detail
Product Introduction
Precision titanium bushings are drawing-controlled turned components used as spacers, sleeves, guides or corrosion-resistant interfaces. The order should define bore and outside diameter, fit and tolerance, concentricity, length, flange or shoulder geometry, edge condition, surface finish, grade, quantity and inspection.
Product Specifications
| Product | Precision Titanium Bushings | Grade | Titanium Grade 2, Grade 5 or drawing-specified grade |
|---|---|---|---|
| Standard | The approved component drawing controls geometry and acceptance. Source bar, tube or forging material must be ordered to the applicable product specification and condition. | Size & Form | Straight, flanged, shouldered or grooved bushings; bore, OD, wall and length according to drawing |
| Tolerance | Drawing-defined fit, concentricity, runout, length, surface finish and geometric tolerances | Supply Condition | Turned, bored, grooved and deburred from traceable bar, tube or forging stock |
| Inspection | Material identity and traceability, bore and OD measurement, length, wall and concentricity, thread or gauge checks when applicable, surface finish and agreed first-article report. | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 2 / R50400 | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 5 / R56400 | Al 5.50–6.75; V 3.50–4.50 | 0.40 | 0.20 | 0.08 | 0.05 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 2 | 345 MPa | 275 MPa | 20% |
| Grade 5 | 895 MPa | 828 MPa | 10% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 8.6 µm/m·K |
| Grade 5 | 4.43 g/cm³ | Approx. 114 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Products are separated by grade and heat, protected against surface and dimensional damage, and packed with traceability labels according to form, size, quantity and shipping method.
Application Scenarios
Valve, pump and process-equipment interfaces
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Aerospace and precision motion assemblies
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Marine and corrosion-resistant equipment
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
Which dimensions control bushing fit?
Bore and outside diameter tolerances, roundness, concentricity, wall variation and mating-part dimensions normally control fit.
Can titanium bushings be supplied with a flange or groove?
Yes, when all geometry, radii, chamfers, tolerances and inspection features are defined on the drawing.
How is galling addressed?
Material pairing, clearance, finish, lubrication, coating and operating conditions must be reviewed as a complete tribological system.
Leave Your Message
Related Technical Guides
Hollow Bar for Bushings and Sleeves
Define starting stock, finished geometry and machining allowance.
Read technical guideTitanium CNC Machining Design and RFQ Guide
Prepare drawings, tolerances, surfaces, quantities and inspection requirements.
Read technical guideGrade 2 vs Grade 5 Machined Parts
Compare corrosion, strength and machining requirements.
Read technical guideMachining Tolerance and Inspection Guide
Define dimensional, surface and first-article acceptance.
Read technical guide