Custom Titanium CNC Machined Parts
Custom titanium CNC machined parts manufactured to drawing from traceable Grade 2, Grade 5 or specified titanium stock with controlled dimensions, finish and inspection.
- Materials
- Grade 2, Grade 5 and drawing-specified titanium alloys
- Processes
- CNC turning, milling, drilling, boring and finishing
- Basis
- Approved drawing and source-material specification
- Documents
- MTC, traceability and agreed dimensional records
Product Detail
Product Introduction
Custom titanium CNC machined parts are produced to an approved drawing from traceable plate, bar, tube or forging stock. A complete order defines material grade and source specification, dimensions and datum, tolerances, surface finish, thread and edge requirements, quantity, cleaning, inspection and required records.
Product Specifications
| Product | Custom Titanium CNC Machined Parts | Grade | Titanium Grade 2, Grade 5 or drawing-specified grade |
|---|---|---|---|
| Standard | The finished component is controlled by the approved drawing and purchase order. Source material may be ordered to ASTM B265, ASTM B348, ASTM B381 or another expressly specified standard appropriate to its product form. | Size & Form | Drawing-controlled turned, milled, drilled or bored components; prototype and production quantities by review |
| Tolerance | General and critical dimensions, geometric tolerances, threads and surface finish according to the approved drawing | Supply Condition | Deburred and cleaned; rough-machined, semi-finished or finish-machined with agreed surface treatment |
| Inspection | MTC and heat/lot traceability, visual and dimensional inspection, first-article or CMM report, surface-finish verification, thread gauging and agreed PMI or NDT. | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 2 / R50400 | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 5 / R56400 | Al 5.50–6.75; V 3.50–4.50 | 0.40 | 0.20 | 0.08 | 0.05 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 2 | 345 MPa | 275 MPa | 20% |
| Grade 5 | 895 MPa | 828 MPa | 10% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 8.6 µm/m·K |
| Grade 5 | 4.43 g/cm³ | Approx. 114 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Products are separated by grade and heat, protected against surface and dimensional damage, and packed with traceability labels according to form, size, quantity and shipping method.
Application Scenarios
Chemical and process-equipment components
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Aerospace and high-performance assemblies
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Marine and offshore equipment
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
What files are needed for quotation?
Provide a controlled 2D drawing and, when available, a compatible 3D model. The drawing must control material, dimensions, tolerances, finish, threads, inspection and revision.
Can source-material certificates be supplied?
Yes. State the required material specification, revision, grade, heat traceability and additional test records in the purchase order.
Can prototypes and production quantities be reviewed?
Yes. Quote feasibility depends on geometry, stock, tooling, inspection, quantity and delivery requirements.
Leave Your Message
Related Technical Guides
Titanium CNC Machining Design and RFQ Guide
Prepare drawings, tolerances, surfaces, quantities and inspection requirements.
Read technical guideGrade 2 vs Grade 5 Machined Parts
Compare corrosion, strength and machining requirements.
Read technical guideMachining Tolerance and Inspection Guide
Define dimensional, surface and first-article acceptance.
Read technical guide