Titanium Plate for Chemical Processing Equipment
Titanium plate for chemical equipment supplied by corrosion-selected grade, dimensions, fabrication route, surface, inspection, MTC and project documentation.
- Material
- Titanium Grade 2, Grade 7, Grade 12 or corrosion-selected grade
- Standard
- ASTM B265 / ASME SB265 plus approved equipment design requirements
- Product Form
- Sheet, plate and cut blanks; thickness, width, length, flatness and edge condition are confirmed by RFQ
- Documents
- MTC, inspection and heat/lot traceability
Product Detail
Product Introduction
Titanium Plate for Chemical Processing Equipment is supplied for corrosion-resistant fabrication and precision manufacturing. The final purchase definition must identify the exact material designation, governing specification and revision, dimensions, condition, tolerances, tests and documentation; trade-name or cross-standard equivalence is not assumed.
Product Specifications
| Product | Titanium Plate for Chemical Processing Equipment | Grade | Titanium Grade 2, Grade 7, Grade 12 or corrosion-selected grade |
|---|---|---|---|
| Standard | ASTM B265 / ASME SB265 plus approved equipment design requirements | Size & Form | Plate, sheet and cut blanks for vessels, tanks, liners, covers, internals and fabricated process components |
| Tolerance | Governing material standard or approved customer drawing | Supply Condition | Hot or cold rolled, annealed, pickled, blasted, brushed or polished as applicable |
| Inspection | MTC review, dimensional and surface inspection, heat/lot traceability, with PMI or applicable NDT when specified | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 2 / R50400 | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 2 | 345 MPa | 275 MPa | 20% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Sheet and plate surfaces are interleaved or wrapped as required, protected at edges and secured on pallets or in export cases with grade, heat and dimensional identification. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.
Application Scenarios
Chemical vessels, tanks and process equipment
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Liners, covers, baffles and corrosion-resistant internals
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Heat-exchanger, acid-processing and chlor-alkali fabrication
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
What information is required to quote Titanium Plate for Chemical Processing Equipment?
Provide the titanium grade, product form, dimensional standard or drawing, thread or critical dimensions, quantity, surface treatment, mating parts, service conditions and required inspection documents.
Which standards apply to Titanium Plate for Chemical Processing Equipment?
ASTM B265 / ASME SB265 plus approved equipment design requirements
How are Titanium Plate for Chemical Processing Equipment inspected?
MTC review, dimensional and surface inspection, heat/lot traceability, with PMI or applicable NDT when specified
Leave Your Message
Related Technical Guides
Hot Rolled vs Cold Rolled Titanium
Compare thickness range, surface, flatness, forming and machining considerations.
Read technical guideHow to Specify ASTM B265 Titanium Plate
Define grade, dimensions, condition, tolerance, surface, tests and certification.
Read technical guideThickness, Tolerance and Flatness Guide
Prepare dimensional requirements that match fabrication and machining needs.
Read technical guideChemical Processing Plate Selection
Review service chemistry, grade, fabrication, inspection and documentation.
Read technical guide