Large Diameter Titanium Fittings
Large Diameter Titanium Fittings supplied by titanium grade, outside diameter or NPS, wall thickness, end preparation, dimensional standard and inspection requirements for corrosion-resistant piping systems.
- Material
- Titanium Grade 2, Grade 7 or Grade 12 as specified
- Product Standard
- ASTM B363 / ASME SB363 where applicable
- Dimensions
- ASME B16.9, B16.11 or approved drawing
- Documents
- MTC, dimensions and heat/lot traceability
Product Detail
Product Introduction
Large-diameter titanium fittings are elbows, tees, reducers, caps or drawing-specific transitions whose size, wall or forming envelope exceeds common standard-stock ranges. The defining issue is scale: plate development, segmentation, forming, weld layout, roundness, handling, heat treatment, NDE and shipping must be engineered for the specific diameter and wall.
Product Specifications
| Product | Large Diameter Titanium Fittings | Material Options | Titanium Grade 2, Grade 7 or Grade 12 as specified |
|---|---|---|---|
| Forms | Large-diameter or drawing-specific fabricated fitting | Typical Inquiry Range | OD, wall, geometry, tolerances and end preparation controlled by approved drawing |
| Product Standard | ASTM B363 / ASME SB363 where applicable | Dimensional Basis | ASME B16.9, ASME B16.11 or approved drawing as applicable |
| Wall | Schedule or nominal wall thickness matched to the connected pipe and design | Ends | Welded, machined, flanged or project-defined ends |
| Manufacturing | Seamless, welded, formed, forged, machined or fabricated as specified | Surface | Pickled, cleaned, machined or project-specific finish |
| Inspection | Visual, dimensions, wall, ends and specified NDT | Documents | MTC, heat/lot traceability and inspection report |
Typical ranges are quotation guidance, not a stock guarantee. Final availability and tolerances are confirmed against the complete RFQ and design code.
Selection and Configuration
- Size and wall envelope: Provide OD or NPS, nominal and minimum wall, overall dimensions and connected-pipe tolerances.
- Formed or fabricated route: Confirm hot forming, cold forming, pressed halves, gore segments or welded fabrication and permitted weld layout.
- Inspection and logistics: Define dimensional survey, roundness, wall mapping, weld NDE, pressure test when required, lifting points and shipping limits.
Send the piping specification or drawing
Include grade, NPS or OD, wall/schedule, geometry, ends, quantity, tests and documents.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered grade controls.
| Grade / UNS | Pd | Mo / Ni | Fe | O | C | N | H | Ti |
|---|---|---|---|---|---|---|---|---|
| Grade 2 / R50400 | — | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 7 / R52400 | 0.12–0.25 Pd | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 12 / R53400 | — | 0.20–0.40 Mo; 0.60–0.90 Ni | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
Mechanical Properties – Annealed Source Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 2 | 345 MPa (50 ksi) | 275 MPa (40 ksi) | 20% |
| Grade 7 | 345 MPa (50 ksi) | 275 MPa (40 ksi) | 20% |
| Grade 12 | 483 MPa (70 ksi) | 345 MPa (50 ksi) | 18% |
Representative wrought-source material minima. Fitting acceptance, heat treatment and test specimens must follow the ordered material/product specification and size.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Conductivity | Thermal Expansion |
|---|---|---|---|---|
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 16.4 W/m·K | Approx. 8.6 µm/m·K |
| Grade 7 | Approx. 4.51 g/cm³ | Approx. 105 GPa | Approx. 16 W/m·K | Approx. 8.6 µm/m·K |
| Grade 12 | Approx. 4.54 g/cm³ | Approx. 103 GPa | Approx. 16 W/m·K | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Fittings are capped or wrapped to protect clean ends, bevels, threads and machined faces. Items are separated by grade, size and heat/lot, then packed in reinforced cartons or export cases according to geometry and quantity.
Application Scenarios
Chemical Processing
Corrosion-resistant piping for acids, chlorides and process media after grade compatibility review.
Power & Energy
Cooling-water, condenser and auxiliary piping requiring traceable titanium components.
Marine & Desalination
Seawater and chloride-bearing piping systems designed for the selected titanium grade.
FAQ
What makes a titanium fitting large diameter?
It is a procurement category for sizes beyond common seamless or standard-stock ranges; exact limits depend on geometry, wall, material route and manufacturing capability.
Are large fittings always fabricated?
Not always, but forming and source-stock limits often make welded or segmented construction necessary. The approved route must be stated.
Which shipping data is needed?
Provide destination, maximum shipping envelope and weight, lifting or support needs, protection and any site-assembly constraints.
Leave Your Message
Related Technical Guides
Titanium Butt Weld Fittings Purchasing Matrix
Compare geometry, size, wall, ends, route and inspection.
Read technical guideTitanium Fittings for Seawater Piping
Coordinate material, piping design, fabrication and inspection.
Read technical guideTitanium RFQ Checklist
Prepare complete purchasing data and documents.
Read technical guide