Titanium Square Bar

Solid four-sided titanium bar for keys, tooling blanks, supports and CNC components whose finished envelope benefits from a square starting section. Quote side A, diagonal or squareness method, corner condition, cut length, straightness, twist, manufacturing route and inspection separately.

Material
Grade 2 / UNS R50400; Grade 5 / UNS R56400; Grade 23 / UNS R56407
Side A
6–100 mm common market RFQ reference
Diagonal D
1.4142 × A theoretical perfect-square value
Cut Length L
1,000–3,000 mm common market RFQ reference
CONTACT US

Product Detail

Product Introduction

Titanium square bar is a solid section with four equal nominal sides and four longitudinal corners. It is used when a four-sided starting envelope can reduce removal compared with round bar, but side size alone does not define a usable square bar. A purchase description should state side A and tolerance, diagonal or out-of-square acceptance, corner radius or chamfer, straightness, twist, cut length, end condition, surface and the accepted manufacturing route. Rolled, forged and machined-from-larger-stock square bars can differ in corner fill, grain direction, cleanup allowance, surface and economical quantity, so route and finished-part envelope must be reviewed together.

Selection Priorities

Section definition

State side A and its tolerance, then diagonal limits or an agreed out-of-square method, corner radius/chamfer, cut length and end condition. For a theoretical perfect square, D ≈ 1.4142 × A; actual rounded or chamfered corners require drawing-defined measurement points.

Squareness and twist

Measure both side dimensions and diagonals at agreed stations. Define twist separately as an angular or face-displacement limit over a stated gauge length; one acceptable cut-end cross-section does not control whole-length geometry.

Route and allowance

Identify whether rolled, forged or machined square stock is acceptable. Provide finished dimensions, datum strategy and machining allowance so all faces and corners clean up without purchasing unnecessary titanium.

Grade and service

Choose Grade 2, Grade 5, Grade 23 or another specified grade from corrosion, strength, fatigue, temperature, joining and finished-component requirements. Appearance does not establish grade.

Product Specifications

ProductTitanium Square BarGradeTitanium Grade 2 / UNS R50400, Grade 5 / UNS R56400, Grade 23 / UNS R56407 or specified grade
StandardASTM B348/B348M-25 is the primary current American material reference for covered annealed titanium and titanium-alloy bars and billets; ASME SB348 may be invoked for applicable projects. JIS H 4650:2016 explicitly covers square as well as circular, rectangular and regular-hexagonal titanium bar sections. ISO 7217:2023 with Amendment 1:2024 and GB/T 2965-2023 can be reviewed for international enquiries when the exact grade, form, condition, revision and tests are supplied. GOST or EN/DIN requirements can be reviewed only against the identified document and drawing. These specifications are not automatically equivalent, and none replaces finished-component drawing controls.Size & FormCommon market RFQ reference: side A 6–100 mm and cut lengths 1,000–3,000 mm. These values help prepare an inquiry and are not an inventory statement or unconditional capability promise.
ToleranceOrder-defined side A, diagonal/out-of-square method, corner condition, straightness span and limit, twist gauge length and limit, cut length, end condition, surface and cleanup allowanceSupply ConditionRolled, forged or machined square bar only when the proposed route is accepted and recorded; cut and protected to the approved order requirements
InspectionVerify material identity and heat/lot traceability, both side dimensions and diagonals at agreed stations, corner radius or chamfer, cut length, end condition, straightness, twist, surface and the approved manufacturing route. Product test certificates can be provided.DocumentsProduct test certificates can be provided.

Additional Supply & Ordering Details

Useful, technically consistent information consolidated from earlier product pages.

Section boundaryTitanium square bar is four-sided solid stock with equal width and height. Specify side dimension, corner radius, diagonals, squareness, twist, straightness and length.
Stock-shape decisionSquare stock suits blocks, keys, tooling blanks and four-sided machined parts. It is not interchangeable with hex bar because the finished geometry, corner locations and machining yield differ.
Manufacturing routeRolled, forged or machined square bar can have different grain orientation, corner shape and surface. State whether sharp, radiused or machining-allowance corners are required.
Inspection focusMeasure side dimensions and diagonals, squareness, corner radii, twist, bow, cut length and surface condition, maintaining heat/lot identification.

Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.

Request a Quotation

Chemical Composition

Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.

Grade / UNSPrincipal Alloying ElementsFe maxO maxC maxN maxH maxTi
Grade 2 / R50400—0.300.250.080.030.015Balance
Grade 5 / R56400Al 5.50–6.75; V 3.50–4.500.400.200.080.050.015Balance

Mechanical Properties – Annealed Material Reference

GradeUltimate Tensile Strength min0.2% Yield Strength minElongation min
Grade 2345 MPa275 MPa20%
Grade 5895 MPa828 MPa10%

Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.

Typical Physical Properties

GradeDensityElastic ModulusThermal Expansion
Grade 24.51 g/cm³Approx. 105 GPaApprox. 8.6 µm/m·K
Grade 54.43 g/cm³Approx. 114 GPaApprox. 8.6 µm/m·K

Typical engineering references, not inspection acceptance limits.

Certificates & Inspection Records

Order documentation: Product test certificates can be provided. The RFQ should identify the material, heat/lot, test and dimensional records required for the order.

Services We Can Provide

Section ReviewSide, diagonal/out-of-square method, corners, length and cleanup envelope checked together.
Route ReviewRolled, forged or machined route recorded for approval and certificate mapping.
Twist ControlGauge length, angular or face-displacement method and limit defined by the order.
Dimensional InspectionSide and diagonal mapping, corners, straightness, twist, length and surface checked to the approved plan.
TraceabilityMaterial identity and heat/lot records maintained through cutting and packing.
Protected PackingFaces, corners and straight lengths separated and protected against impact and bending.

Product Packaging

Bars and rods are separated by grade and heat, protected against surface damage and secured in bundles or export cases with identification and traceability labels. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.

Bundled titanium bars and rods protected for export

Application Scenarios

Keys, tooling blanks and support blocks with a four-sided envelope

Define finished side envelope, corner cleanup, datum faces, length, load direction and machining allowance before choosing the starting section.

Valve, pump and instrument components machined from square stock

Provide service chemistry, design conditions, ports, sealing or bearing faces, machining allowance and final inspection requirements; material certification does not certify the finished component.

CNC-machined brackets and corrosion-resistant components retaining square geometry

Use the finished drawing to control faces, corners, datums, holes, threads, surface and dimensional reporting, and compare square stock with plate-cut or forged routes on yield and inspection.

FAQ

How is titanium square bar measured?

State side A between opposite faces, then add its tolerance, diagonal or out-of-square method, corner condition, cut length, straightness, twist and end requirements. Measure at agreed stations rather than only at one cut end.

What is the diagonal of a square titanium bar?

For a theoretical perfect square, D = A × √2, or approximately 1.4142 × A. Actual rounded or chamfered corners change the practical contact points, so the approved drawing and inspection method control acceptance.

Is square bar interchangeable with flat bar or a plate-cut block?

No. Square bar has equal nominal sides; flat bar is rectangular, and plate-cut or forged blocks can differ in grain direction, edge condition, flatness, allowance and certificate mapping. Approve the route before ordering.

Does ASTM B348/B348M-25 define the finished square component?

No. It is a material specification for covered titanium bars and billets. The purchase order and finished-component drawing must separately control square geometry, machining, datums, tolerances and final acceptance.

Are 6–100 mm sides and 1,000–3,000 mm lengths in stock?

No stock claim is made. They are common market RFQ references for inquiry preparation. Final availability and manufacturing feasibility are confirmed from the grade, route, exact size, tolerance, quantity and inspection package.

Can product test certificates be provided?

Yes. Product test certificates can be provided. State the required chemistry, mechanical-property, heat/lot traceability and dimensional-inspection scope in the RFQ.

Leave Your Message

Related Technical Guides

WhatsApp