Titanium Grade 9 Coil
Titanium Grade 9 Ti-3Al-2.5V coil and slit strip supplied by thickness, width, coil dimensions, edge condition, surface, condition, inspection and certification requirements.
- Material
- Titanium Grade 9 / Ti-3Al-2.5V / UNS R56320
- Standard
- ASTM B265 / ASME SB265
- Product Form
- Coil, slit strip or cut length
- Documents
- MTC, dimensions and heat/lot traceability
Product Detail
Product Introduction
Titanium Grade 9 coil uses the Ti-3Al-2.5V alpha-beta alloy where higher strength than commercially pure titanium is required with useful formability and low mass. The approved order must define specification and revision, thickness, width, coil dimensions and weight, edge and surface condition, heat treatment, tolerances, tests and traceability.
Product Specifications
| Product | Titanium Grade 9 Coil | Grade | Titanium Grade 9 / Ti-3Al-2.5V / UNS R56320 |
|---|---|---|---|
| Standard | ASTM B265 / ASME SB265 includes Grade 9 / UNS R56320 strip, sheet and plate when expressly invoked. Aerospace applications may require a different material specification; the applicable standard and revision must be stated rather than inferred from the alloy name. | Size & Form | Thickness, width, coil inside/outside diameter, maximum coil weight and slit or mill-edge condition are confirmed by RFQ |
| Tolerance | ASTM B265 / ASME SB265 or tighter order-defined thickness, width, camber and edge requirements | Supply Condition | Annealed or order-specific condition; coil or precision slit strip with agreed surface and edge condition |
| Inspection | MTC and heat/lot identity review, chemistry and mechanical results, thickness and width, coil geometry and weight, surface and edge examination, plus agreed supplementary testing. | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 9 / R56320 | Al 2.50–3.50; V 2.00–3.00 | 0.25 | 0.15 | 0.08 | 0.03 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 9 | 620 MPa | 485 MPa | 15% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 9 | Approx. 4.48 g/cm³ | Approx. 105 GPa | Approx. 9.0 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Coils and slit strip are wrapped against moisture and edge damage, secured on skids or in export cases, and labeled with grade, heat, size, coil weight and edge condition. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.
Application Scenarios
Aerospace and lightweight formed components
Material grade, dimensions, condition and inspection must be matched to the application requirements.
High-performance heat-exchanger and tubing fabrication
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Marine and industrial equipment
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
What is Titanium Grade 9 coil?
Grade 9 is Ti-3Al-2.5V / UNS R56320, an alpha-beta titanium alloy offering higher strength than commercially pure grades while retaining useful forming characteristics. Final suitability depends on condition, dimensions and the component manufacturing route.
Does ASTM B265 apply to Grade 9 coil?
ASTM B265 / ASME SB265 covers Grade 9 strip, sheet and plate when expressly ordered. Aerospace projects may invoke another specification, so the RFQ must state the controlling document and revision.
What information is needed for quotation?
Provide material grade, standard and revision, condition, thickness, width, coil ID and OD, maximum coil weight, edge, surface, quantity, application, tests and documents.
Leave Your Message
Related Technical Guides
Titanium Coil Purchasing Matrix
Compare grades and define coil geometry, edge, surface and processing.
Read technical guideHow to Choose a Titanium Grade
Compare titanium grades by strength, corrosion environment and fabrication needs.
Read technical guideTitanium RFQ Checklist
Prepare dimensions, standards, tests and documentation.
Read technical guideComplete Titanium Product Guide
Compare coil and strip with other titanium product forms.
Read technical guide