Titanium Grade 4 Pipe & Tube
Titanium Grade 4 Pipe & Tube supplied to the specified dimensions, condition, tolerance, inspection and material-traceability requirements for industrial procurement.
- Material
- Titanium Grade 4 / UNS R50700
- Standard
- ASTM B338, ASTM B861 or ASTM B862 as applicable
- Product Form
- Seamless or welded pipe/tube; OD or NPS, wall thickness, length and end condition are confirmed by RFQ
- Documents
- MTC, inspection and heat/lot traceability
Product Detail
Product Introduction
Titanium Grade 4 Pipe & Tube is supplied for corrosion-resistant fabrication and precision manufacturing. The final purchase definition must identify the exact material designation, governing specification and revision, dimensions, condition, tolerances, tests and documentation; trade-name or cross-standard equivalence is not assumed.
When is Grade 4 pipe or tube considered?
Selection answer: Grade 4 is the strongest commonly specified commercially pure grade and may be considered where higher pressure-design strength is needed while remaining within a CP titanium material family.
Selection boundary: Higher material strength does not by itself establish pressure rating, and reduced forming latitude may affect bends or expanded tube ends. The construction code and product standard still control.
RFQ data to confirm: State product form and standard, OD or NPS, wall, design pressure and temperature, bending or expansion operations, manufacturing route, tests and acceptance criteria.
Product Specifications
| Product | Titanium Grade 4 Pipe & Tube | Grade | Titanium Grade 4 / UNS R50700 |
|---|---|---|---|
| Standard | ASTM B338, ASTM B861 or ASTM B862 as applicable | Size & Form | Seamless or welded pipe/tube; OD or NPS, wall thickness, length and end condition are confirmed by RFQ |
| Tolerance | Governing material standard or approved customer drawing | Supply Condition | Annealed and pickled seamless or welded product with specified ends |
| Inspection | MTC review, dimensional and surface inspection, heat/lot traceability, with PMI or applicable NDT when specified | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 4 / R50700 | — | 0.50 | 0.40 | 0.08 | 0.05 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 4 | 550 MPa | 483 MPa | 15% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 4 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Pipe and tube ends are capped, surfaces are wrapped where required, and bundles or export cases are identified by grade, size, heat and quantity. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.
Application Scenarios
Chemical processing equipment
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Marine and desalination systems
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Industrial fabrication and precision components
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
What information is required to quote Titanium Grade 4 Pipe & Tube?
Provide the titanium grade, product form, dimensional standard or drawing, thread or critical dimensions, quantity, surface treatment, mating parts, service conditions and required inspection documents.
Which standards apply to Titanium Grade 4 Pipe & Tube?
ASTM B338, ASTM B861 or ASTM B862 as applicable
How are Titanium Grade 4 Pipe & Tube inspected?
MTC review, dimensional and surface inspection, heat/lot traceability, with PMI or applicable NDT when specified
Leave Your Message
Related Technical Guides
How to Choose a Titanium Grade
Compare grade, strength, corrosion environment and fabrication needs.
Read technical guideTitanium RFQ Checklist
Prepare dimensions, standards, tests and documentation.
Read technical guideComplete Titanium Product Guide
Compare titanium product forms and sourcing considerations.
Read technical guide