Precision Titanium Strip
Precision titanium strip supplied by grade, thickness, slit width, edge condition, camber, flatness, surface, coil dimensions and certification requirements.
- Grades
- Grade 1, Grade 2, Grade 5 or specified alloy
- Standard
- ASTM B265 / applicable AMS or customer specification
- Form
- Precision slit strip and narrow coil
- Documents
- MTC and dimensional inspection
Product Detail
Product Introduction
Precision titanium strip is narrow cold-rolled or slit product supplied where thickness, width, edge quality, camber, flatness and winding quality affect downstream stamping, forming, welding or assembly. The exact grade and product specification must be stated because one set of properties does not apply to every titanium alloy.
What makes a titanium strip order precision-controlled?
Selection answer: Precision strip is defined by tighter and application-specific control of thickness, width, edge, camber, flatness, coil geometry and surface rather than by the word precision alone.
Selection boundary: A nominal grade and size do not establish stamping, spring, welding or continuous-processing performance. The acceptable mill route, slit-edge condition, burr direction, mechanical properties and inspection frequency must match the downstream line.
RFQ data to confirm: Provide grade and specification, thickness and tolerance, width and tolerance, coil ID/OD and weight, slit edge and burr limits, camber and flatness, surface, temper or condition, application, sampling plan, total quantity and certificates.
Product Specifications
| Product | Precision Titanium Strip | Grade | Titanium Grade 1, Grade 2, Grade 5 or specified alloy |
|---|---|---|---|
| Standard | ASTM B265 / ASME SB265 may control commercially pure and alloy strip where applicable. Aerospace strip may require an expressly invoked AMS specification. The purchase order controls grade, condition, dimensions and supplementary inspection. | Size & Form | Narrow slit strip or coil; thickness, width, coil ID/OD, maximum weight and cut-length option by RFQ |
| Tolerance | Order-defined thickness, width, camber, flatness, edge and burr limits | Supply Condition | Cold rolled, annealed and slit; pickled, bright or order-defined surface with protected edges |
| Inspection | MTC review, thickness and width measurement, camber and flatness, slit-edge and burr inspection, surface examination, coil build and heat/lot traceability. | Documents | MTC, heat/lot traceability and agreed inspection reports |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| Grade 1 / R50250 | — | 0.20 | 0.18 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 2 / R50400 | — | 0.30 | 0.25 | 0.08 | 0.03 | 0.015 | Balance |
| Grade 5 / R56400 | Al 5.50–6.75; V 3.50–4.50 | 0.40 | 0.20 | 0.08 | 0.05 | 0.015 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| Grade 1 | 240 MPa | 170 MPa | 24% |
| Grade 2 | 345 MPa | 275 MPa | 20% |
| Grade 5 | 895 MPa | 828 MPa | 10% |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| Grade 1 | 4.51 g/cm³ | Approx. 103 GPa | Approx. 8.6 µm/m·K |
| Grade 2 | 4.51 g/cm³ | Approx. 105 GPa | Approx. 8.6 µm/m·K |
| Grade 5 | 4.43 g/cm³ | Approx. 114 GPa | Approx. 8.6 µm/m·K |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Coils and slit strip are wrapped against moisture and edge damage, secured on skids or in export cases, and labeled with grade, heat, size, coil weight and edge condition. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.
Application Scenarios
Precision stamped and formed parts
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Aerospace and industrial shims
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Chemical and electrochemical components
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
What makes titanium strip a precision product?
The order controls tighter or function-specific thickness, width, camber, flatness, edge, burr, surface and coil-build requirements.
Can Grade 2 and Grade 5 use the same forming process?
Not automatically. Their strength and formability differ, so grade, condition, tooling, bend radius and process qualification require separate review.
What information is needed for quotation?
Provide grade, thickness and tolerance, width, edge and burr, camber, surface, coil dimensions, weight, quantity, tests and certificates.
Leave Your Message
Related Technical Guides
How to Specify Titanium Coil
Define processing-line geometry and precision strip controls.
Read technical guideTitanium Foil vs Strip vs Sheet
Compare thickness, delivery form and tolerances.
Read technical guideTitanium RFQ Checklist
Define grade, dimensions and documents.
Read technical guideComplete Titanium Product Guide
Compare product forms and sourcing.
Read technical guide