TC11 Titanium Alloy Bar
TC11 Titanium Alloy Bar supplied to the specified dimensions, condition, tolerance, inspection and material-traceability requirements for industrial procurement.
- Material
- TC11 / Ti-6.5Al-3.5Mo-1.5Zr-0.3Si
- Standard
- GB/T 2965 or aviation customer specification
- Product Form
- Round bar, rod and cut blanks; diameter, length, straightness and machining allowance are confirmed by RFQ
- Documents
- MTC, inspection and heat/lot traceability
Product Detail
Product Introduction
TC11 Titanium Alloy Bar is supplied for corrosion-resistant fabrication and precision manufacturing. The final purchase definition must identify the exact material designation, governing specification and revision, dimensions, condition, tolerances, tests and documentation; trade-name or cross-standard equivalence is not assumed.
Product Specifications
| Product | TC11 Titanium Alloy Bar | Grade | TC11 / Ti-6.5Al-3.5Mo-1.5Zr-0.3Si |
|---|---|---|---|
| Standard | GB/T 2965 or aviation customer specification | Size & Form | Round bar, rod and cut blanks; diameter, length, straightness and machining allowance are confirmed by RFQ |
| Tolerance | Governing material standard or approved customer drawing | Supply Condition | Hot rolled, forged, annealed, peeled, pickled or ground as specified |
| Inspection | MTC review, dimensional and surface inspection, heat/lot traceability, with PMI or applicable NDT when specified | Documents | MTC, heat/lot traceability and agreed inspection reports |
Additional Supply & Ordering Details
Useful, technically consistent information consolidated from earlier product pages.
| Product naming consolidated | TC11 titanium alloy bar and TC11 titanium rod are consolidated on this primary page because both describe the same solid bar product family. |
|---|---|
| Alloy identity | TC11 is commonly described by the nominal Ti-6.5Al-3.5Mo-1.5Zr-0.3Si composition family. The controlling GB/T or aviation customer specification must be named rather than assuming ASTM equivalence. |
| Supply definition | State diameter, length, heat-treatment condition, ultrasonic inspection class, surface condition, machining allowance and dimensional tolerances. |
| Quality documentation | MTC, heat traceability, chemistry, mechanical test results, dimensional inspection and agreed NDE records can be reviewed against the purchase specification. |
Send the complete material RFQ
Include grade, specification revision, dimensions, tolerance, quantity, condition, tests and destination.
Chemical Composition
Weight percent; maximum unless a range is shown. Titanium is the balance. The ordered specification and grade control.
| Grade / UNS | Principal Alloying Elements | Fe max | O max | C max | N max | H max | Ti |
|---|---|---|---|---|---|---|---|
| TC11 | Al 5.8–7.0; Mo 2.8–3.8; Zr 0.8–2.0; Si 0.20–0.35 | 0.25 | 0.15 | 0.08 | 0.05 | 0.012 | Balance |
Mechanical Properties – Annealed Material Reference
| Grade | Ultimate Tensile Strength min | 0.2% Yield Strength min | Elongation min |
|---|---|---|---|
| TC11 | 1030 MPa reference | 900 MPa reference | 10% reference |
Representative minima only. Product form, section size, heat treatment and the invoked specification determine the certified acceptance values.
Typical Physical Properties
| Grade | Density | Elastic Modulus | Thermal Expansion |
|---|---|---|---|
| TC11 | Approx. 4.5 g/cm³ | Verify against approved engineering data | Verify against approved engineering data |
Typical engineering references, not inspection acceptance limits.
Certificates & Inspection Records
Services We Can Provide
Product Packaging
Bars and rods are separated by grade and heat, protected against surface damage and secured in bundles or export cases with identification and traceability labels. Typical export packaging for the same physical product form is shown below; final packing is confirmed for each order.
Application Scenarios
Chemical processing equipment
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Marine and desalination systems
Material grade, dimensions, condition and inspection must be matched to the application requirements.
Industrial fabrication and precision components
Material grade, dimensions, condition and inspection must be matched to the application requirements.
FAQ
What information is required to quote TC11 Titanium Alloy Bar?
Provide the titanium grade, product form, dimensional standard or drawing, thread or critical dimensions, quantity, surface treatment, mating parts, service conditions and required inspection documents.
Which standards apply to TC11 Titanium Alloy Bar?
GB/T 2965 or aviation customer specification
How are TC11 Titanium Alloy Bar inspected?
MTC review, dimensional and surface inspection, heat/lot traceability, with PMI or applicable NDT when specified
Leave Your Message
Related Technical Guides
How to Choose a Titanium Grade
Compare grade, strength, corrosion environment and fabrication needs.
Read technical guideTitanium RFQ Checklist
Prepare dimensions, standards, tests and documentation.
Read technical guideComplete Titanium Product Guide
Compare titanium product forms and sourcing considerations.
Read technical guide